FAQs
Questions about our solid-state battery tech? We’ve got answers.
Solid-state technology
A solid-state lithium-metal battery is a battery that replaces the polymer separator and liquid electrolyte used in conventional lithium-ion batteries with a solid-state separator. The replacement of the separator enables the carbon or silicon anode used in conventional lithium-ion batteries to be replaced with a lithium-metal anode. The lithium-metal anode is more energy dense than conventional anodes, allowing the battery to store a greater amount of energy in the same volume. Some solid-state designs use excess lithium to form the anode, but the QS design is ‘anode-free’ in that the battery is manufactured anode free in a discharged state, and the anode forms in situ on the first charge.
Relative to a conventional lithium-ion battery, solid-state lithium-metal battery technology has the potential to increase the cell energy density (by eliminating the carbon or carbon-silicon anode), reduce charge time (by eliminating the charge bottleneck resulting from the need to have lithium diffuse into the carbon particles in conventional lithium-ion cell), prolong life (by eliminating capacity fade that results from the unwanted chemical side reaction between the carbon and liquid electrolyte in conventional lithium-ion cells), improve safety (by eliminating the combustible organic porous separator and organic anolyte material in conventional cells) and lower cost (by eliminating the anode materials and manufacturing costs). Designing a lithium-metal battery that can deliver on this potential is not easy, and many lithium-metal technology approaches fail to achieve the promised benefits. In contrast, QS’s proprietary ceramic separator is a unique technology approach that has been shown to deliver improvements in all of these aspects of battery performance.
The higher energy density of QS solid-state lithium-metal cells, at our commercial target of 800–1,000 Wh/L, could translate to more range in the electric vehicle, depending on the vehicle design. For example, a vehicle that gets ~350 miles of range on a single charge using one of today’s leading conventional lithium-ion cells with an energy density of ~700 Wh/L, could get between 400 and 500 miles of range using QS cells.
The actual range attainable by a car depends on many factors, and vehicle designers may choose to optimize for range, cost, space, or other factors, and these design choices will impact the range of the vehicle.
Most of the benefits of solid-state stem from the ability to use lithium metal as the anode. Using lithium-metal as the anode requires a solid-state separator that prevents dendrites and does not react with lithium. Once you have such a separator, you can use lithium-metal as the anode and realize the benefits of higher energy density, faster charge, and improved life and safety. QS has developed such a separator based on its proprietary ceramic material and uses a pure lithium-metal anode with zero excess lithium to deliver the above benefits. In the QSE-5 cell design, QS couples this solid-state ceramic separator with an organic liquid electrolyte for the cathode (catholyte). The ceramic separator also enables our battery design to use a customized catholyte material, better suited for the voltage and transport requirements of the cathode. The requirements for the ceramic separator are different from that of the catholyte. The former requires dendrite resistance and stability to lithium-metal. The latter requires high conductivity (given the thicker cathode), high voltage stability (given the cathode voltage), and the ability to make good contact with the cathode active material particle. It is difficult to find materials that meet both these requirements and attempts to do so often result in a material that meets neither requirement well, resulting in cells that can fail from dendrite formation while also not providing sufficient conductivity to run at high power. In other cell designs, QS technology may be paired with a solid catholyte, resulting in an all-solid-state battery.
Specific energy is the term physicists use to refer to gravimetric energy density (Wh/kg), whereas energy density is the term they use to refer to volumetric energy density (Wh/L). A cell with higher specific energy will save weight in the batteries themselves and provide additional weight savings in the battery system. Less weight in the car from a lighter battery system can then reduce chassis weight, tires, brakes, and more, which can improve vehicle performance and efficiency.
A cell with higher volumetric energy density will reduce the size of the modules and pack. This, too, has follow-on benefits at the system level, requiring fewer connectors and cables, and allowing for safe design of the vehicle with more room for crumple zones, as well as more comfort with more room for passengers and cargo.
QS’s solid-state lithium-metal battery technology is designed to provide both high specific energy and high energy density.
The QS separator material is a ceramic capable of meeting the key requirements of high conductivity, stability to lithium metal, resistance to dendrite formation, and low interfacial impedance. These are the key requirements to make a lithium-metal anode, which in turn enables high energy density, fast charge, and long life. The ceramic itself is non-combustible, making it safer than conventional polymer separators, which are hydrocarbons and so can burn. The formulation of QS’s material is proprietary, but it uses earth abundant materials and is made using a continuous-flow manufacturing process, which we believe will make it cost-effective at commercial volumes.
Ceramics in general are stable to very high temperatures, and our ceramic separator is no exception. In addition, even at very high temperatures, it does not burn (since it is already oxidized), therefore we believe that it will provide a thermally stable barrier between the anode and cathode. Our architecture reduces the fuel content of the cell by removing the conventional polymer separator, graphite and anolyte. Note that safety must be demonstrated using the specific cell and pack design in question, as small design changes can have a significant impact on overall safety behavior.
Our 24-layer A0 prototype cell has completed more than 1,000 full charge-discharge cycle equivalents with more than 95% discharge energy retention. We believe this is due to the fundamental properties of our technology, including the extremely high Coulombic efficiency of our ceramic separator and anode-free cell design.
QS technology is based on a solid ceramic separator and lithium-metal anode which is designed to be anode-free as manufactured. We believe this design is ideal for maximizing solid-state battery performance. However, we also believe this design is cathode compatible; that is, this same technology can be paired with a variety of cathode materials and still deliver valuable performance improvements. This could potentially include solid-state cathodes which are being developed by automakers and batteries companies. Because it is cathode compatible, QS technology can be seen as complementary to those other technology approaches rather than competing with them.
Over the years, people have tried to develop solid-state batteries with materials such as polymers, sulfides, oxides, liquids, and composites (which are a mix of other materials, such as polymers and ceramics). We are not aware of any of these efforts being successful on the metric of delivering long cycle life at high rates of power without requiring elevated temperatures. Most importantly, to the best of our knowledge, none of the competing approaches have presented data showing they are able to prevent dendrites (lithium growths that short circuit batteries) at room temperature and automotive current densities. To date, the principal way that these competing approaches have avoided dendrites is by compromising test conditions (i.e. low power, short-cycle life, raising the temperature, etc.). It took us over 10 years, over two million tests, and hundreds of millions of dollars of investment in R&D to get to the level of performance we have demonstrated, so we believe this is a very hard problem and will be difficult for competitors to solve.
Headline energy density figures are often misleading. These figures are sensitive to test conditions and can appear higher if, for example, unrealistically slow discharge rates are used. If test conditions are not disclosed, it’s hard to make apples-to-apples comparisons across different batteries. In addition, batteries that are optimized for energy density frequently make compromises on other performance characteristics which may result in poor power performance, slow charging, low cycle life, or worse safety.
In contrast, QS always discloses the test conditions we use to measure our energy density so that you can draw meaningful conclusions about our technology performance. In addition, QS technology enables cutting-edge energy density in a system that also offers high power, fast charging, good cycle life and an improved safety profile. We believe this is a compelling value proposition that is unmatched in the industry.
Conventional lithium-ion batteries are used to provide backup power and load-smoothing inside data centers, but the volatile chemistry of these batteries has led to a series of damaging fires inside data centers that endanger human lives, incur costly downtime and put million-dollar AI chips at risk. QS batteries can provide high-quality power to the valuable chips inside AI data centers while offering a safer solid-state design that we believe reduces the risk of fires, all in a smaller footprint that makes the most of the valuable real estate inside AI data centers.
QS’s solid-state lithium-metal battery technology is developed in the U.S. and eliminates dependence on graphite anodes, the supply chain for which is highly concentrated in China. QS technology therefore helps eliminate key bottlenecks and improves supply chain resilience.
QS is currently shipping solid-state batteries to customers from our own production facility in San Jose, California. At the same time, we are working with ecosystem partners to scale up additional manufacturing capacity to serve the large and growing markets for solid-state batteries in automotive, AI data center, aerospace, defense, consumer electronics and other applications.